Baller Nando Posted October 7, 2018 Baller Share Posted October 7, 2018 When winterizing my boats, I've always run antifreeze through AND drained everything. I used 2 gallons of antifreeze and all that came out when draining was antifreeze. This year, mainly because the block plugs on my 196 are so difficult to get at, I decided to fill everything with antifreeze and leave it. I used 4 gallons and did drain the water pump and manifolds, mainly because I wanted to make sure any scale came out (virtually none). What came out of the manifolds and water pump was pure antifreeze. Now I'm afraid of cracking my block. Will it be safe? Was 4 gallons adequate? Should I climb back in and drain the block? Link to comment Share on other sites More sharing options...
Baller Andre Posted October 7, 2018 Baller Share Posted October 7, 2018 You're fine. You did drain the engine BEFORE filling with anti freeze ? My ski finish in 16.95 but my ass is out of tolerance! Link to comment Share on other sites More sharing options...
Baller Jmoski Posted October 7, 2018 Baller Share Posted October 7, 2018 +1 on drain first, then back fill with marine AF. If you don’t drain first the AF will be diluted.... Link to comment Share on other sites More sharing options...
Baller Ski_Dad Posted October 8, 2018 Baller Share Posted October 8, 2018 i would drain the block - i think what's in there is pretty diluted if you didn't drain it 1st. Link to comment Share on other sites More sharing options...
Baller BraceMaker Posted October 8, 2018 Baller Share Posted October 8, 2018 How much went into your block and how much went into the exhaust manifolds. There are a few different routings that marine raw water cooling can be piped. However the general architecture on a boat is, raw water pump pushes water into thermostat housing, there is a bypass that goes to a J tube to the recirculation pump and the block. That pump pushes fluid through the block where it is restricted from exiting by the thermostat. The rest of the fluid goes through the tubes from the housing to the manifolds and exits with the exhaust. So when you want to push pink juice into the block you really need to make sure the block is either empty (drained first) or that the thermostat is open (engine hot) otherwise what can happen is that the raw water pump will push most of your antifreeze out into the manifolds and exhaust and there can be a "charge" of water that was held into the block by the thermostat. So that's your risk really is that if the thermostat was not open most of the juice gets bypassed. Where as if its drained first it will pull pure pink juice into the block. If it is hot enough for the thermostat to open the engine only holds a few gallons of fluid and the return will initially get diluted and some pulled back through from the circulation pump. But as you continue to add new that improves. Link to comment Share on other sites More sharing options...
Baller Jmoski Posted October 8, 2018 Baller Share Posted October 8, 2018 I used to warm up the engine, drain and then pull AF from a bucket. But now I drain, then pull off the hose to the starboard manifold and pour AF directly into the block. A gallon into the block and 1/2 gallon to get the heater. Link to comment Share on other sites More sharing options...
Baller WBLskier Posted October 8, 2018 Baller Share Posted October 8, 2018 So I always understood that you needed the engine at operating temp before sucking the antifreeze through. If the block and manifolds have been drained before am I now correct in understanding that warming the engine up is not necessary? I've been draining the block and manifolds at the boat launch, sucking 1 gallon through the intake, fogging it, and then filling the manifolds and block from the top with a funnel. If I don't have to worry about heating the engine up as long as the block and manifolds were drained I'll go back to just sucking 5 gallons through the intake hose. Any suggestions appreciated. Link to comment Share on other sites More sharing options...
Baller Jmoski Posted October 8, 2018 Baller Share Posted October 8, 2018 @WBLskier -your current protocol is good, but you probably have an empty block. If you are going to pull AF from a bucket via a hose connected to the intake at the water strainer, yes you want it warmed up to ensure the thermostat is open and routing AF to the block. Make sure you rinse off the impeller after as the AF will cause it to swell. I would not trust using the AF to force out the water as there will be mixing and churning in both the block and the manifolds - leaving you with an unknown dilution % of the AF. What I do (after draining) is use the hose that sends water from the block to the exhaust manifold to pour the AF in (backwards) into the block. You can verify it is hitting the block by leaving the drain plugs loose as you start to pour, you will find one side fills before the other. Getting AF in the block is a good extra measure, but the most important step is fully draining the water out - regardless of how you get the AF in there. Link to comment Share on other sites More sharing options...
Baller Nando Posted October 8, 2018 Author Baller Share Posted October 8, 2018 Boat was warmed up, pulled intake hose off water strainer and poured 4 gallons into intake hose while running engine at about 1500 RPM. I figure that with a warm engine if it was pure antifreeze coming out the exhaust, I’m good, but there’s this lingering doubt... Link to comment Share on other sites More sharing options...
Baller Jmoski Posted October 8, 2018 Baller Share Posted October 8, 2018 @Nando - how cold does it get where you are? In regards to “pure” AF coming the exhaust, how do you know that? I sleep better at night knowing my block is safe, yes accessing the drain plugs on the block is a pain, but not nearly as painful as replacing the engine, unless you really wanted the 6L with Zero off anyways :smiley: Link to comment Share on other sites More sharing options...
Baller oldjeep Posted October 8, 2018 Baller Share Posted October 8, 2018 I really don't understand some of this thinking. Every fall there are threads about how to shortcut winterization by not draining the block, and every spring threads about cracked blocks. If you cant do it right, pay someone. Link to comment Share on other sites More sharing options...
Baller_ MISkier Posted October 9, 2018 Baller_ Share Posted October 9, 2018 This is how I have seen it done at the dealer: 1. Warm engine to full operating temperature using flush suction cup installed on raw water intake and connected to water source. Shut off and remove flush suction cup. 2. Drain block by removing drain plugs on both sides of engine (or opening automotive radiator drains, if installed on block). 3. Drain risers/manifolds by disconnecting the garden hose union from the riser/manifolds that is located at the back of the engine. 4. Remove circulating pump hose and allow excess water to drain. 5. Remove water hose to transmission cooler and allow excess water to drain. Use finger to ensure transmission cooler is free of debris and not retaining any water. 6. Drain heater by disconnecting the heater lines from the engine and blowing low pressure (max 10 psi) air through the disconnected heater lines (I have radiator flush tees on my heater hoses, so just need to remove those caps to drain and flush with air). Reconnect heater hoses (or close flush tees). 7. Open shower head and run shower pump to remove excess water from that system. Shut off shower pump when water no longer emerges. 8. Run engine for 10 seconds max to push any remaining water through pump and through engine. 9. After all drains no longer have water running, close drains and shower head. 10. Connect antifreeze source (7 gallons for engine, heater, shower) to flush suction cup, install flush suction cup to raw water intake, and start engine to draw in antifreeze with raw water pump. 11. Open shower head an run shower pump until antifreeze emerges. Shut off shower pump and close shower head. 12. Check exhaust for antifreeze to emerge. Turn off engine when antifreeze source is exhausted and ensure it does not run dry beyond the available antifreeze source. 13. Change oil and filter. The worst slalom equipment I own is between my ears. Link to comment Share on other sites More sharing options...
Baller Drago Posted October 9, 2018 Baller Share Posted October 9, 2018 * if you have PerfectPass, disconnect speedo tubes where they enter the PP black box Link to comment Share on other sites More sharing options...
Baller oldjeep Posted October 9, 2018 Baller Share Posted October 9, 2018 The most important step is 2a which is stick a screwdriver in the block drains a few times to make sure they are not clogged with rust flakes. When i winterized the inlaws lxi yesterday it happened again that one side acted empty and then gushed after the screwdriver treatment. Link to comment Share on other sites More sharing options...
Baller_ DW Posted October 9, 2018 Baller_ Share Posted October 9, 2018 And always do both block drains. Link to comment Share on other sites More sharing options...
Baller MNshortliner Posted October 9, 2018 Baller Share Posted October 9, 2018 The “Don’t fix it, if it ain’t broke” line seems to come to mind. If you have been winterizing your boat for years and haven’t had a problem don’t change it now. Link to comment Share on other sites More sharing options...
Baller BraceMaker Posted October 9, 2018 Baller Share Posted October 9, 2018 @Drago thats the Medallion gauges pressure transducer not PP related. In those boats PP only gets speed from a paddlewheel. But yes if you still have a working medallion gauge system drain that and replace it with a short length of tubing then an aquarium filter so water doesnt destroy your box. Link to comment Share on other sites More sharing options...
Baller Nando Posted October 9, 2018 Author Baller Share Posted October 9, 2018 @Jmoski- cold enough to freeze the balls off a brass monkey. In South Canada. My boat came from real Canada (though south of me) and has a thermostatic marine heater in the bilge that would prevent freezing, except there's no electricity where I store it. Ironically, the location of that heater is one of the reasons it's so difficult to get to the block plugs. I had also thought that keeping antifreeze in the block would help prevent corrosion, to some degree. Link to comment Share on other sites More sharing options...
Baller Jmoski Posted October 9, 2018 Baller Share Posted October 9, 2018 @Nando - have you considered removing the heater since your not using it anyways? Or do you have power at the dock to let you run late in the Fall? If it was my boat, I would drain the block to be 100% sure, especially given the prolonged cold your boat will be exposed to. Out of curiousity, what was the freeze protection level (-50, -100) of the AF you put in? If you used the -100 F I’d say your good as that can be diluted and still give you enough protection. Starbrite makes a -200 F AF with corrosion inhibitors- that might be the trick for you... Link to comment Share on other sites More sharing options...
Baller Nando Posted October 10, 2018 Author Baller Share Posted October 10, 2018 No heater, no shower, no PP (ZO). It was -50. I think I'll be pulling the block plugs... Link to comment Share on other sites More sharing options...
Baller BMG73 Posted October 11, 2018 Baller Share Posted October 11, 2018 I don’t get why some of you guys mess with the antifreeze. Drain it. Link to comment Share on other sites More sharing options...
Baller thager Posted October 11, 2018 Baller Share Posted October 11, 2018 @BMG73 I used to only drain and noticed large amounts of scale over the years. One year water did not drain from a manifold due to that scale me thinks and I got to replace a cracked manifold. Now I drain then fill with anti-freeze. Scale problem is pretty much nonexistent now. Link to comment Share on other sites More sharing options...
Baller Drago Posted October 20, 2018 Baller Share Posted October 20, 2018 @BraceMaker Pull the speedo tubes out of your PP master module if you have one. May have been because it was oriented straight up, but I had one freeze the little plastic inlet tube and crack it many yrs ago Link to comment Share on other sites More sharing options...
Baller BraceMaker Posted October 20, 2018 Baller Share Posted October 20, 2018 @Drago Oh wow thats vintage PP. Rev 4? You can still install aquarium filters to help keep water away from it just like a medallion. Makes it easier to separate the hoses and blow em out. Link to comment Share on other sites More sharing options...
Baller Drago Posted October 21, 2018 Baller Share Posted October 21, 2018 Cool idea, thanks. I assume it’s OG (‘97 nautique, my Lake Powell boat.) I just crank up the kx , check the Rs with my phone, and free ski with it Link to comment Share on other sites More sharing options...
Baller Zman Posted October 21, 2018 Baller Share Posted October 21, 2018 As @thager said, the engine block will scale if you don't refill with 50/50 mix of antifreeze. Plus, if you do, your boat is nearly ready to go come good weather. Hoses connected, plugs in. Unless, like me now, you live in the south and only drain for brief periods. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now