Baller ozski Posted March 5, 2015 Baller Share Posted March 5, 2015 As the title says @ 1500 hours and the PCM (6.0) is sucking oil and pretty much ready for a rebuild despite regular services. I would have expected greater longevity but running a decent amount of jump and 36MPH maybe 1500 is about par? Is this because they run such high RPM's? Thoughts? Link to comment Share on other sites More sharing options...
Baller GAJ0004 Posted March 5, 2015 Baller Share Posted March 5, 2015 Get a compression check done first. If the numbers are still good hold off on the rebuild. Is it sucking down oil in less than 50 hours? I Link to comment Share on other sites More sharing options...
Baller skihacker Posted March 6, 2015 Baller Share Posted March 6, 2015 this is a longshot but take a good long look at the pcv/breather parts, a modern well serviced motor burning oil is pretty rare nowadays, might be something else going on. Link to comment Share on other sites More sharing options...
Baller_ Bruce_Butterfield Posted March 6, 2015 Baller_ Share Posted March 6, 2015 Get it checked out. At only 1500 hrs there is most likely something else going on. Do you have an Oz version of @Jody_Seal ? If it was easy, they would call it Wakeboarding Link to comment Share on other sites More sharing options...
Baller_ DW Posted March 6, 2015 Baller_ Share Posted March 6, 2015 I would add a leak down test for additional diagnosis. Breather / PVC system is also a good suggestion. Have you looked at the plugs? What is the oil consumption level? Link to comment Share on other sites More sharing options...
Baller liquid d Posted March 6, 2015 Baller Share Posted March 6, 2015 You don't need an OZ version of Jody...he's there! Link to comment Share on other sites More sharing options...
Baller ozski Posted March 6, 2015 Author Baller Share Posted March 6, 2015 Thanks everyone I will pass the suggestions on, this engine had to be repaired / replaced at 170 hours from new. I spent a few hours behind the wheel yesterday and its certainly not down on power but it needs oil daily. Link to comment Share on other sites More sharing options...
Baller_ RichardDoane Posted March 6, 2015 Baller_ Share Posted March 6, 2015 next oil changfe, I'd recommend changing to a different weight/viscosity of engine oil, and see if there is a decrease in consumption Link to comment Share on other sites More sharing options...
Baller Keith_Menard Posted March 6, 2015 Baller Share Posted March 6, 2015 +1 on the leakdown. Link to comment Share on other sites More sharing options...
Baller swc5150 Posted March 6, 2015 Baller Share Posted March 6, 2015 First 6.0 I've heard of with this issue, but I know of a hand full 5.7 200's that needed replacing. I wonder if there was a small batch of bad blocks or something? I don't recall hearing any issues during the 196 years, but there definitely could've been some? I hope this one is solved without a full rebuild, Link to comment Share on other sites More sharing options...
Baller ozski Posted March 6, 2015 Author Baller Share Posted March 6, 2015 What constitutes a handful of 5.7's? Enough to consider this to be a "known issue"? @OB how many is a few others? Link to comment Share on other sites More sharing options...
SFinn Posted March 6, 2015 Share Posted March 6, 2015 @ozski if you are near Albury contact Engine Master Australia (EMA) they are the PCM dealer for Aus. I had some issues with my Ex330 that the other Nautique mechanics had no idea what was wrong with it. I took it up to them and they are miles ahead of the the other guys Link to comment Share on other sites More sharing options...
JJVDMZN Posted March 6, 2015 Share Posted March 6, 2015 I had a rusted oil sump on a 2009 Malibu RLXI, 350 Monsoon, did 550hrs. At first I thought it was the Crank shaft Oil seal. Changed the sump to Aluminium sump, problem solved. Link to comment Share on other sites More sharing options...
Baller swc5150 Posted March 6, 2015 Baller Share Posted March 6, 2015 @ozski What OB said. There's also a guy on PN from Canada, if not included in OB's circle. Link to comment Share on other sites More sharing options...
Baller skierjp Posted March 6, 2015 Baller Share Posted March 6, 2015 If it was a bad block it would have probably been using oil from the beginning. I don't see PCM covering it with 1500 hours on it. Link to comment Share on other sites More sharing options...
Baller jjackkrash Posted March 6, 2015 Baller Share Posted March 6, 2015 I've heard from a number of different marine mechanics over the years that 1500 hours is about average on a marine gas V-8 before an overhaul if those are actually 1500 working hours, and not just idle or the key turned on listening to the stereo hours. I also hear a lot of anecdotal tales of engines going much longer, but I wonder about the actual usage of those engines. Link to comment Share on other sites More sharing options...
Baller swc5150 Posted March 6, 2015 Baller Share Posted March 6, 2015 That's interesting... Depending on the circumstances, I'd think it may take a while to reach 1,500 working hours? For example, my wife and I just bought an '06 196. We went over our diacom reading with the PCM tech who ran it, which was very informative. Of the 671 hours on the clock, 462 were between 0-1,000rpms, with only 111 hours between 3,001 & 4,000 (slalom speed obviously). Even better, only 2.2 hours registered between 4,001 & 5,000. He said we bought a gently used engine, that should last a long, long time. It might be interesting to compare a diacom from an engine needing an "early" rebuild? Link to comment Share on other sites More sharing options...
Baller_ Jody_Seal Posted March 6, 2015 Baller_ Share Posted March 6, 2015 Always remember anything build by man is doomed to failure sooner or later! I have seen engines run 2000 hours under general waterski service and run as clean and have near as much power as when they were first put into service. I have also seen engines ventilate the engine block in less the 50 hours under general water ski service. so far I have seen some pretty good advice about doing a thorough diagnostic of the engine. Many times owners think because their engine is only a few years old that it does not need things like PCV valve, ignition wires, etc. get these items checked out. Have a compression and leak down test performed. Run the diacom diagnostic's.. Another word of advice if indeed the engine is in need of replacement, If you plan on running another 1500 plus hours of service on the engine I would not rebuild it. Sell your core to some hotrodder and buy a new service long block. it has been my experience that for longevity one is better off buying new then rebuild. My .02 cents Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now